變速箱維修后是否會有什么影響？維修后有影響，只有兩點關重要的原因，一個是維修人員的技術水平不夠穩，工作不夠仔細，第二點就是配件問題。下面濟南自動變速箱維修人員把這兩點分為四點來細說：

Will there be any impact after gearbox maintenance? After maintenance, there are only two crucial reasons for the impact. One is that the technical level of maintenance personnel is not stable enough and their work is not meticulous enough, and the second is the issue of accessories. The Jinan automatic transmission maintenance personnel will divide these two points into four points to elaborate on:

一，維修技師在維修前是否能精準判斷故障點。

1、 Can the maintenance technician accurately determine the fault point before maintenance.

一個經驗豐富的維修技師，通過檢查故障代碼，試車或是車主的口述，即可快速的說出具體的故障，這樣的話，在維修時候就沒有了盲，拆卸時候只需要更換損壞配件，再認真檢查其他沒有故障的配件，做好防御工作即可了。而如果沒有時間判斷出故障點的話，在拆掉時候就會很迷茫，逐一排查，很浪費時間經歷，到后即使換了一圈配件，也不見得會修好。

An experienced maintenance technician can quickly identify the specific fault by checking the fault code, conducting a test drive, or the owner's dictation. This way, there is no need to be blind during maintenance. When disassembling, all you need to do is replace damaged parts, carefully inspect other parts that are not faulty, and do a good job of defense. If the fault point is not identified in the first place, it will be very confusing when dismantling, troubleshooting one by one, and it is a waste of time and experience. Even if a circle of accessories is replaced, it may not be repaired.

二，維修技師在維修時候有沒有認真判斷好損壞的主要原因和間接原因。

2、 Did the maintenance technician carefully determine the main and indirect causes of the damage during maintenance.

其實除了油封之外，還有很多造成漏油的間接原因。就比方說是定位環，限位墊片。原車的定位環是橡膠材質的，很容易出現老化變稀的情況，改進的為剛性定位環，可以避免故障。而限位墊片是表面磨光了，改進的限位墊片做了加長，表面還有耐磨層，延長使用壽命。

In fact, besides oil seals, there are many indirect causes of oil leakage. For example, it is a positioning ring or a limit washer. The original car's positioning ring is made of rubber material, which is prone to aging and thinning. The improved rigid positioning ring can avoid malfunctions. The limit washer has a polished surface, and the improved limit washer has been lengthened with a wear-resistant layer on the surface, extending its service life.

三，配件是否改進。

3、 Whether the accessories have been improved.

有些變速箱，比方說是6AT變速箱內部的緩沖片，緩沖片材質太薄承受不住變速箱內部常年高溫，造成的燒蝕斷裂現象，面對于這個情況，很多人會選擇更換原廠的緩沖片，其實這個目前是有改進的加寬加厚的緩沖片了，改進的除了加寬加厚這個優點之外，表面還加上了激光打印的耐磨層，更為耐磨一些。

Some gearboxes, such as the buffer plates inside the 6AT gearbox, have a material that is too thin to withstand the high temperature inside the gearbox, causing erosion and fracture. Faced with this situation, many people choose to replace the original buffer plates. In fact, there are currently improved widened and thickened buffer plates. In addition to the advantage of widening and thickening, the improved buffer plates also have a laser printed wear-resistant layer on the surface, More wear-resistant.

四，維修技師是否認真安裝。

4、 Is the maintenance technician installing it carefully.

在安裝配件時候，如果沒有認真的安裝，擰緊螺絲的話，也是很容易出現后期的故障。所以，在保證配件全部安裝的情況下，還要保證好配件的安裝程度，有沒有松的地方，這一點也是會在維修后，出現故障的?？傊x擇做事認真，、仔細、為您省錢的維修廠，還是關重要的一點的。

If the installation of accessories is not done carefully and the screws are tightened, it is also easy to encounter later failures. So, while ensuring the installation of all accessories, it is also necessary to ensure the installation degree of the accessories and whether there are any loose areas, which can also lead to malfunctions after maintenance. In short, it is crucial to choose a repair shop that is serious, professional, meticulous, and saves you money.

諸如上面類別，變速箱維修后，要想沒有什么影響和故障，那就先注意好維修時候，先了解好愛車裝配的變速箱，是否有改進配件，找的維修技師判斷好問題，裝配件時候也要讓維修技師保證好每個配件的嚴實性，避免后期故障。更多相關事項就來我們網站http://njzhuiri.cn咨詢！

For example, in the above categories, if there are no impacts or malfunctions after gearbox maintenance, it is important to first pay attention to the maintenance process. First, understand the gearbox installed in your car and whether there are any improved parts. Find a professional maintenance technician to determine the problem. When assembling parts, also ask the maintenance technician to ensure the tightness of each part to avoid future failures. For more related matters, come to our website http://njzhuiri.cn consulting service